|
Item |
Description |
Reference |
| Amvic
FormLock™ straight block 4", 6" & 8" |
48" long by 16" high with a concrete core
of 4, 6, or 8 inches respectively. 2 1/2 inches of EPS foam in
each side produces an overall thickness of 9, 11 or 13" respectively. |
Amvic Catalog |
| Amvic
FormLock™ 90-degree corner blocks, 4", 6" & 8" |
|
|
| Amvic
FormLock™ 45-degree corner blocks, 4", 6" & 8" |
|
|
| Amvic
FormLock™ straight block, 10" |
48" long by 24" high with a concrete core
of 10 inches and an overall thickness of 15". |
|
| Amvic
FormLock™ 90-degree corner blocks, 10" |
|
|
| Amvic corner rods |
9'3 square hollow polypropylene tubes that
are inserted in each corner of Amvic blocks |
|
| Amvic Brickledge block |
Used to extend out support at a block line
to provide a base upon which to support the installation of brick above |
|
| Amvic Taper Top block |
Extends concrete infill out to within 1/2"
of outer edge of block on the top of the form. |
|
| Amvic curved block (custom order to your
radius) |
|
|
| V-Buck vinyl buck system- standard |
A cost effective vinyl extrusion system
that is an alternative to pressure treated wood to frame out door and
window openings and provide a fastening system into which to attach doors
and windows |
www.vbuck.com |
| V-Buck vinyl buck custom rounds & shapes |
Special order shapes, rounds, half rounds,
quarter rounds, ovals, etc. of virtually any size. They are pre bent
at the factory in Utah and direct shipped to your site fully assembled and
ready for installation. |
www.vbuck.com |
| Amvic AmDeck™ ICF elevated concrete floor,
deck and roof system |
The most advanced system for creating a
raised concrete floor where the beams supporting the concrete deck are
formed out of concrete and rebar and poured at the same time as the deck.
20 foot spans can be set and poured without temporary shoring.
When temporary shoring is used clear spans up to 40 feet are possible. The
forming system is an EPS form, that stays in place after the floor is
poured and insulates the floor and provides an attaching system for
sheetrock.
|
AmDeck |
| Reechcraft Paneljack Professional ICF
alignment bracing |
An excellent alignment bracing system that
uses an aluminum strongback to reduce per brace weight. The
adjustable kicker and footboard support are made of steel. Braces of
8, 10, 12, 14, 16, 18, and 20' height are available as well as specialized
corner braces. Each brace is 3 pieces and weighs about 50lbs. |
www.reechcraft.com |
| Amvic Plumwall Pro ICF alignment bracing |
A collapsible all steel bracing system that
can be adjusted from the scaffold platform by a single person. Each
brace is a single piece and weighs about 75 lbs. |
|
| Amvic Tall Wall ICF bracing system |
|
|
| ICF Top Plate Sill Gasket |
adhesive membrane on the bottom that is
designed to be used between the concrete at the top of an ICF wall and the
top plate (mudsill). |
Spec sheet |
| ICF EPS foam guns |
|
|
| Foam 2 Foam ICF EPS foam-filler/adhesive |
|
|
| ICF EPS foam cleaner |
|
|
| ICF hot knife kits |
|
|
| ICF waterproofing systems |
|
|
| ePro Ecoline-R Liquid applied waterproofing
membrane for ICF |
Our recommended base coat sealant for below
grade installation |
|
| MiraDrain 2000/6000 dimple drainboard
waterproofing |
The second layer of the recommended
waterproofing system |
|
| Polyguard 650LT ICF-certified waterproofing
sheet membrane |
|
Spec sheet |
| ProtectoWrap ProtectoDrain 2000 foundation
dimple drain board |
|
Spec sheet |
| ProtectoWrap BT20 ICF adhesive window
flashing |
|
Spec sheet |
| |
|
|
| Grappler plates for ICF |
|
|
| ICF rasp for EPS foam, flat |
|
|
| ICF rasp for EPS foam, curved for corner
bullnose |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
